T-HANDLE ALLEN KEY SET Cobra 8 pieces 2 to 10 mm

Regular price: €79.90 (Save €10.00)
Price: €69.90
Tax included

Set of 8 Cobra T-handle hex keys, 2 to 10 mm, in chrome-vanadium steel. Sliding shaft: slide it out to reach a bolt buried in the chassis, or offset it to get the leverage. Wall rack included, every size in its place. Shipped within 24 h.

En achetant ce produit, vous cumulez 5 points de fidélité, soit €0.50 de remise sur votre prochaine commande. Connectez-vous pour cumuler vos points.

What the sliding shaft changes

On a conventional T-handle key the shaft is fixed. You get the length you get, and when the bolt sits deep in the chassis behind the seat, you cannot reach it. Here the shaft runs through the handle and slides freely.

Two positions, two uses. Shaft pushed right out on one side: you gain the reach for a recessed bolt. Shaft offset, T-handle to one side: you get the leverage to crack a tight bolt, with no bar on the handle and no risk to the thread.

The eight sizes, and what they do on a kart

The two you will wear out: 5 and 6 mm. They hold the seat, the bumpers, the floor tray, the sprocket carrier. The 8 mm comes out for axle collars and hubs. The 4 mm for callipers and pedals. The small ones — 2, 2.5 and 3 mm — are for the carburettor, sensors and small brackets. The 10 mm stays at the bottom of the box most of the time, then saves a day.

Technical data

Reference C070T
Brand Cobra
Contents 8 keys + rack
Sizes 2 — 2.5 — 3 — 4 — 5 — 6 — 8 — 10 mm
Type T-handle, sliding shaft
Material Chrome-vanadium steel (CrV)
Tip Male hex
Rack Metal, wall or bench, sizes marked

What the set contains

  • 8 hex keys, T-handle with sliding shaft
  • 1 metal rack with every size marked

Michel’s tip (the mechanic’s corner)

A hex key does not go into a bolt at an angle. Come in crooked and you bear on two edges instead of six: you round the socket, and a rounded bolt deep in a chassis ends up on the end of a drill. Key square, pushed fully home, then turn.

Hex tips have a life. Once a tip starts to feel loose in the bolt it is finished — it will round the next one. Better to replace a key than to drill out a seat bolt.

CrV does not like damp. A key left in a wet box pits in two weekends. Wipe it after the session and put it back on the rack: that is what the rack is for, seeing at a glance which one is missing before you leave the circuit.

Care

  1. Wipe the shafts after every session, especially in damp weather.
  2. A drop of light oil in the handle if the shaft slides poorly.
  3. Check the tips now and then: sharp edges, not rounded.
  4. Store on the rack, every key in its place.

Frequently asked questions

CrV steel — is it any good?
Chrome-vanadium is the standard for quality hand tools: hard, resistant to twisting, and it does not snap clean the way cheap steel does. It just needs to be kept dry.

Does the set cover everything on a kart?
From 2 to 10 mm, yes, for common hex fasteners. Keep open-end spanners and a socket alongside for nuts.

Does the rack fix to a wall?
Yes, it is drilled for it. It also stands on a bench or in the van.

Why a sliding shaft rather than fixed keys?
Because a kart has both recessed bolts and tight bolts, and the two do not come undone with the same shaft length. Here you have both in one key.

  • Brand
  • Reference
    C070T
  • In stock
    5 Items

4 other products in the same category

Loading...
Back to top