Screw h 8x30 cylinder head Rotax (22)

€1.09
  Tax included
Reference: fr411.011

The Screw th m8x30mm (n ° 22) is a high-quality hexagonal head screw used to bridge the cylinder on the motor housing of the Rotax Dd2. With its length of 30 mm and its thread M8It ensures a solid grip in the low engine nets. She works in pairs with the stop washer (n ° 21) to ensure that the cylinder remains perfectly motionless despite repeated explosions.


 The product is in your cart now
Waiting...
Unable to Add to cart
  In stock

Full description: what is the purpose of this piece?

This screw is not a standard DIY screw, it meets strict mechanical requirements for the competition:

  1. Maintenance of compression: By applying a vertical clamping force, it plate the cylinder against the base seal. It is this pressure that guarantees the perfect sealing of the pre-compression chamber.

  2. Shear resistance: On the DD2, the reports of reports create mechanical jerks. This high-class resistance steel screw supports these constraints without stretching or breaking.

  3. Thermal conductivity: Its design makes it possible to support the dilatation cycles of the aluminum cylinder without losing its tightening voltage.

  4. Precision machining: The thread is calibrated to provide maximum intake in motor housings, thus avoiding tearing from the nets during frequent montages and disassemblies.


💡 Michel's trick

"Caution The guys, the screw of 30mm, it's the survival of your crankcase thread! If you use a screw too short, you will tear down the low engine nets. If it is too long, it will go down to the bottom and you will not squeeze at all. My advice: Always check the status of the threads of the screw # 22 before reassemble. If the thread is 'marked' or shiny, change it. A motor housing is more expensive than a new screw!"


🎓 Tuto: Tightening and assembly

  1. Preparation: Clean the screw well in the housing with a blow gun to remove oil or filth residues.

  2. The editing order: First insert the stop washer (N ° 21) on the screw, then pass the set in the cylinder ear.

  3. Tightening to the couple: Screw by hand until contact, then use a torque wrench. The recommended torque for these M8 screws is 24 nm.

  4. Verification: A well-mounted screw must not show manual screw resistance. If it strengthened before touching the cylinder, clean the thread or replace the screw.

fr411.011
5 Items

You might also like

In the same category

This website uses cookies to ensure you get the best experience on our website.Learn more about cookies

User Area

Guest

Login/Register

Forgot your password?

Languages

Currencies

Languages

Currencies

My Cart

Your Cart is Empty
Cart 

Menu

Search

Our Terms

Terms of Service

In case of return product (unless error on our part)
the transport costs are the responsibility of the customer, the return must be in "colissimo signature" obligatorily
We are not responsible for errors in size, color, model, spare parts. Any change will be done at the expense of the customer.
In case of product replacement of the size, color, model, or other, the customer has 14 days to return the products upon receipt of the order
Article 1: DESIGNATION

In the following :

The Seller designates the company LA CALMETTE KARTING, SARL registered at the RCS of NIMES under the number 495333189, whose registered office is located road Saint Chaptes- 30190 LA CALMETTE - France.

The Buyer designates the Seller's customers, whether they act as a professional or an individual.

 

Article 2: FIELD OF APPLICATION - COMMUNICATION- ACCEPTANCE

These General Conditions of Sale (hereinafter referred to as the "GTC") constitute the sole basis of the commercial negotiation between the Seller and the Buyer.

They are intended to define the conditions in which the Seller provides its Products to the Purchasers and apply, without restriction or reservation, to all sales made by the Seller to Buyers, either directly or through its website online sales www.magickart.eu and www.magickart.fr (hereinafter referred to as the "Site").

In accordance with Article L. 441-6, I paragraph 1 of the French Commercial Code, they are systematically communicated to any Buyer who so requests, to enable him to place an order with the Seller. They are also accessible on the Site.

Any order of Products addressed to the Seller implies, on the part of the Buyer, the unconditional acceptance of these Terms, the acknowledgment of being fully aware of it and the waiver of its possible general conditions of purchase.

The Seller reserves the right to modify its Terms and Conditions at any time. If this is the case, the GCS applicable to the Buyer will be those in force on the date of the order.

 
Article 3: SPECIAL CONDITIONS OF SALE

The special conditions granted to the Buyer are applicable only if they have been the subject of an express, prior and written agreement of the Seller. Only the points explicitly mentioned in this express, prior and written agreement constitute a derogation from the GSC, which, for the rest, apply in full.

 
Article 4: DEFINITION, USE AND AVAILABILITY OF PRODUCTS

4.1. Product Features

The Products offered for sale by the Seller, in its brochures and catalogs as on the Site, are described in the most precise and explicit way possible. The choice and the purchase of a Product under the sole responsibility of the Buyer, it is his responsibility to refer to the product description, brochures, catalogs or the Site, to know the essential characteristics before all orders. It is also the responsibility of the Purchaser to ask for clarification if it deems it necessary to ensure the adequacy of the Product to the needs and use for which it intends the Product. The photos of the Products, whatever their media, are not contractual.

4.2. Availability

The offers of Products presented by the Seller on its brochures and catalogs as on its Site are valid while stocks last.

The Seller reserves the right, at any time, to delete or modify a Product, without notice.

In the event of total or partial unavailability of Products after placing the order, the Buyer will be informed by email as soon as possible of the unavailability of the Product (s) and the total or partial cancellation of his order.

In the event of total or partial cancellation of the order:

- The order of the Buyer will be validated and his bank account will be debited for the entire order;

- The Seller will contact the Buyer to inform him of the cancellation of his order and offer to renew his order, with the exception of the Product not available;

- The Buyer will be delivered Products available;

- The Buyer will be refunded the price of the ordered Product not available as soon as possible and, at the latest, within 30 days of the payment of the sums he has paid.

In accordance with Article L. 121-11 of the Consumer Code, the Seller reserves the right to refuse, for legitimate reason, any order placed by a consumer Buyer that would suggest that he carries out an economic activity in connection with the Products ordered or, more generally, including for a professional Buyer, any abnormal order within the meaning of the relevant case law.

Rule 2

Here is the rule 2 content

Rule 3

Here is the rule 3 content