Propel the aerodynamic performance of your chassis at the top with the full front panel OTK M11 (Nassau Panel manufacturer Original OTK Kart Parts). Intended to equip the latest generations of chassis of the Italian group, including the famous Tony Kart Racer 401 T and Racer tdx, This official component is the result of advanced technological development.
The Research & Development Department ofOTK Kart Group has led a hard design work, combining engineering simulations CFD (Mechanics of digital fluids) Ultra-pushed and multiple test sessions in actual blower. Validated on the international slopes by the factory pilots of the Tony Kart Racing Team, The single profile of the M11 penetrates the air with a formidable efficiency, reducing the overall aerodynamic drag of the kart while optimally guiding the flow of air around the pilot. This optimization results in a measurable advanced speed gain at the end of a straight line.
Regulation & Integration of the M11 Kit:
Entirely in accordance with the technical and safe standards of the FIA, this panel benefits from the official approval 012.BP.70.
Important compatibility note: The M11 evolution focuses on the front fairing (Front panel Nassau and bumper spoiler). If you update your body, be aware that the lateral pontoons / bumper as well as the rear protection from the previous kit M10 remain unchanged and remain perfectly compatible.
👨🔧-. The Tip in Michel (the corner of the expert)
* "Hi pole hunters position! When the R & D department ofOTK sort a new piece of bodywork like this Nassau M11, we do not just talk about aesthetics or shiny plastic. Karting aerodynamics, that's what makes the difference between doubling at the end of the straight line or staying stuck in the cockpit.
My old pistard trick for mounting your M11: the alignment of the fixations and the care of the deco kit !
For the airflow to slide as on a mirror, your M11 panel must be perfectly aligned in the center, without any mechanical tension on its metal column supports. If you go through it by forcing on the fastening legs, the plastic will spin and you will deform the aerodynamic profile calculated in wind tunnel !
Second Small Board Board: This panel receives full whip all splashing, brake dust and gravel. Before sticking your new Tony Kart or Magickart official kit very new, clean the factory plastic body to the brake degreaser and then pass a vitre or isopropyl alcohol. Slightly heat the plastic with a hair dryer so that the vinyl glue is fused perfectly. A well-posed deco kit, without air bubbles on the profiled edges of the M11, it is efficiency and style guaranteed! "*
📐 - The mounting guide & installation: step by step
1.POSE OF EXISTING CARENING:5 min.Put the kart on his stand trolley. Unscrew the upper bindings and the lower pin that maintain your old front panel (M10 or anterior generation). Remove the panel gently.
2.Verification of supports:5 min.Inspect the metal supports attached to the frame and the steering column. If they have suffered shocks in a previous race, straighten them properly for them to be perfectly straight.
3.Ajustement nassau Panel M11:10 min.Present the new Nassau M11 in front of the supports. Follow the tip in Michel: Engage the lower fixation and the upper hand fasteners. Adjust the position for it to be perfectly centered with the steering wheel axis.
4.Verrouillage and management control:5 min.Tighten the mounting nuts without overwriting rubber rings (silent-blocks). Turn the steering wheel from left to right to confirm that the M11 fairing does not rub over your steering rods or on your hands in the cockpit.
❓ - FAQ SEO (Frequently Asked Questions)
Q: Does this M11 panel adapt on the old versions of Tony Kart Racer 401 S or EVX ?
A: Yes I do. The distance of the front body metal supports on the frame remains greatly standardized at OTK. You can install this modern M11 panel on an older chassis to give it a visual boost and enjoy the aerodynamic gain, provided you have the mounting brackets compatible with the M11 shape.
Q: Is the frontal panel M11 delivered with its sticker kit (deco kit) ?
A: Not. As is the standard for the original bodywork, the Nassau Panel M11 is delivered "naked", injected into the official plastic Tony Kart (or white / black depending on the factory). The brand's graphic kits and stickers are sold separately in our dedicated category.
Q: Is this fairing mandatory to participate in international competitions FIA Karting ?
A: For international or national tests requiring the last technical approval in force for the bodywork, the complete pack before M11 (Spoiler + Nassau) responding to the certification form 012.BP.70 is indispensable. Get closer to the specific technical regulations of your championship to validate the compliance of your category.