TMKART water cylinder water fitting

Tmkart CYL.61mm 

The Exhaust manifold D2 (2-sprink flange) is the strategic link between your cylinder and your exhaust system. Designed to meet growing gas flows of new engines, this flange has become the standard for the entire venting engine line Tmkart.

That you rout with a legendary Kz10b or with the last generation blocks R1, R2 or the brand new R3This collector guarantees perfect alignment of the conduit for fluid evacuation and without losses of burned gases.

Product Full Description: Original TM Kart Furnishing Chamber - For KZ-R2 & KZ-R3 Engines - Sizes 3.3 to 3.6

Adjust the compression ratio and the dynamic behavior of your gearbox engine with the Combustion chamber (cylinder head dome) origin TM Kart for KZ-R2 and KZ-R3 engines. Key element of the high motor, the profile of this dome directly determines the volume of the chamber, the height of SQUISH and the combustion speed of the air / gas mixture.

CNC machined with micrometric precision in the workshops of the Italian factory TM Kart, this room guarantees optimal thermal dissipation and a perfect centering in your cylinder head. Proposed in different variations ranging from 3.3 to 3.6, it adapts both on the block Kz-r2 only on the last Kz-r3. It allows you to change your motorization according to your needs: lower dimensions (3.3 / 3.4) To promote explosion, couple and slow turn output, up to higher ratings (3.5 / 3.6To release the top plans, offer an exceptional straight line and prevent the risk of hot weather detonation.

The 0.30 mm base gasket is an important thickness in the adjustment range Tmkart. By raising the three tenths cylinder, you move the opening times of your transfers and your exhaust light up.

This is the privileged setting for fast circuits with long straight lines because it allows the engine to "better breathe" in the towers. This seal is perfectly compatible with the entire line of gear motors: KZ10B, R1, R2 and the new R3

Adjust the compression ratio and the dynamic behavior of your gearbox engine with the Combustion chamber (cylinder head dome) origin TM Kart for KZ-R2 and KZ-R3 engines. Key element of the high motor, the profile of this dome directly determines the volume of the chamber, the height of SQUISH and the combustion speed of the air / gas mixture.

CNC machined with micrometric precision in the workshops of the Italian factory TM Kart, this room guarantees optimal thermal dissipation and a perfect centering in your cylinder head. Proposed in different variations ranging from 3.3 to 3.6, it adapts both on the block Kz-r2 only on the last Kz-r3. It allows you to change your motorization according to your needs: lower dimensions (3.3 / 3.4) To promote explosion, couple and slow turn output, up to higher ratings (3.5 / 3.6To release the top plans, offer an exceptional straight line and prevent the risk of hot weather detonation.

The Full cylinder head KZ-R2-R3 black total is not just a piece of style; It is a critical component for the performance of your engine. This special version benefits from full black surface treatment which, beyond its devastating look, promotes thermal dissipation.

Designed specifically for the engine TMKART KZ-R2-R3It optimizes the flow of coolant around the combustion chamber to maintain constant performance, even during the most trying finals under strong heat.

The Copper cylinder head gasket 0.05 mm is the finest thickness available for engines TM KZ-R2- R3. In a competition motor as the KZ, every hundredth of a millimeter count. This seal makes it possible to adjust with surgical precision your squish (Height between the piston and the cylinder head at the high-standing point) to optimize the combustion without risking the detonation.

The choice of copper guarantees excellent thermal conductivity between the cylinder and the cylinder head dome, thus promoting a homogeneous cooling.

The Copper cylinder head gasket 0.10 mm is probably the most used thickness by KZ drivers. It is the ideal adjustment base for the engine Tmkart kz-r2. This seal makes it possible to obtain a powerful volumetric ratio while maintaining a necessary thermal safety margin during the disputed finals.

Thanks to its pure copper composition, it provides ultra-fast heat transfer to the cooling circuit, thus avoiding the phenomena of detonation (rattling) that often occur with joints of less good quality.rt

Screw TCEI 6x35 Uni 5931-Cylinder head screw for Motor TM KART

Maximize the ignition efficiency and power of your engine thanks to the bougie BRISK SILVER L08S ignition. Specially developed for the extreme requirements of motorsport and competition karting, this bougie is a real reference for exploiting all the potential of the trademark engines Tm kart (Categories KZ with gearbox and monovynesses).

Its peculiarity lies in the use of a Central electrode in pure silver. Money is the best electricity and heat conductor of all metals (even exceeding platinum and iridium). This property allows the BRISK L08S to deliver a spark of a remarkable energy with a lower voltage, while dissipating the heat accumulated in the high speed combustion chamber. This results in a faster flame start, a more homogeneous combustion of the air / gas mixture and an extremely frank accelerator response throughout the range of use of your TM block (KZ10 to the latest KZ-R3).

Guarantee a surgical alignment of your high-engine on the bas-engine thanks to the Cylinder centering sleeve 10.5 x 14 mm original TM KART. Small by size but capital for the efficiency and reliability of your 125cc gear motorization, this rectified steel ring ensures the absolute position of your cylinder compared to the housings.

On the Official Exploded View (Tavola 1 - Cylinder and Engine Head KZ-R3 / R2), this centering is the Landmark n ° 22. Slipdled around the base studs (marker 21) to the junction between the low-engine crankcase and the cylinder base (marker 12), it neutralizes the mechanical games at the editing. It guarantees the perfect continuity between the transfer ducts of the housing and those of the cylinder, thus maximizing the scanning of the gases while eliminating any shear stress on the studs during the tightening of the nuts (marker 20).